What are your insights and beliefs on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging project. If the old bathtub is readily easily accessible, the project can relocate quickly; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the new one. See to it you have certified yourself for the task and fit trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your restroom if you have actually already purchased a brand-new bathtub and don't require to change the plan of your previous water system pipes.
Your tools and also material checklist must consist of the following:
Getting ready for the Installment
First of all, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipes. Once the supply pipelines have been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, place the bath tub in the needed placement. The wood boards are helpful in equally spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bath tub up until the level checks out degree.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as additionally check the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will certainly resolve it into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area between the tap and the sink. Protect the faucet in position with the supplier provided backnut. Once the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be linked to the tap finishes first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, causing the water to permeate the wall in between the bathroom and also the tiling, bring about issues with moisture as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that post about Installing A Bathtub when doing a search on the search engines. Sharing is nice. Who knows, you could be doing someone a favor. Kudos for your time. Come back soon.
Booking Page